美军作战试验与鉴定发展研究

当前,军队装备试验鉴定正由性能试验向作战试验、在役考核全领域拓展。在装备试验鉴定体系全面重塑的历史背景下,为适应军队装备试验鉴定发展新变化,探索装备试验鉴定新理论,推进装备试验鉴定自主创新发展,亟需开展装备试验鉴定技术研究。美军相对较早开展了装备试验与鉴定工作,在作战试验与鉴定工作方面已形成了较完善的法规制度体系和规范的操作流程,有较成熟的理论与方法成果可供借鉴。与此同时,美军作战试验与鉴定工作也面临许多新问题。本文剖析了美军作战试验与鉴定的内涵和管理模式,研究了2018和2019年美军作战试验与鉴定的重点技术领域,并进行了对比分析,以期掌握近期美军作战试验与鉴定工作的发展变化。     

【专栏】飞机结构静强度应变现场测试手段展望

目前飞机结构静强度应变现场主要的测试手段为使用电阻应变计测量系统，但电阻应变计测量系统存在抗电磁干扰差、引线过多以及一致性难以保证等问题，测试效果难以保证。近年来，光纤传感以及非接触光学测量手段的迅速发展，为飞机结构静强度应变现场测试提供了多种选择。本文通过分析以数字图像相关法技术为代表的新技术的特点，如通过进行非接触操作消除安装过程中所带来的分散性误差以及不确定性，在应对某些需要定性分析的飞机静强度试验场合时可以实时给出三维应变和位移场数据，使测量技术更加直观，以及可溯源性更好、更容易保证计量特性的稳定等，对未来飞机结构静强度应变现场测试手段进行了展望，以期为相关部门和机构提供参考。     

FlexRay在导弹测试系统中的应用

针对导弹测试系统可靠性差、通信速率低的缺点,在分析测试需求的基础上,提出了一种基于Flex Ray总线技术的导弹测试系统总体设计方案,给出了数字信号处理器与总线控制器的接口硬件电路、软件流程,分析了设计中需要考虑的主要问题。     

水下缩比航行体热尾流的红外探测实验

根据缩比模型,建立缩比红外成像实验测试系统,对水下航行体的体积、航行深度、运动速度、尾流排放等进行缩比设计,设计多种实验工况,可实现缩比目标模型红外尾流的静态和动态测试。一方面明确红外尾流的可探测性,另一方面掌握红外尾流可探测性的影响因素以及红外尾流的变化规律,为下一步工作奠定基础。缩比实验结果表明,利用区域灰度均值和均方差的起伏变化可有效探测水下航行体水面尾迹。     

Priori information analysis of optocoupler accelerated degradation experiment based on failure mechanism verification test

The optocoupler is a weak link in the inertial navigation platform of a kind of guided munitions. It is necessary to use accelerated storage test to verify the storage life of long storage products. Especially for small sample products, it is very important to obtain prior information for the design and implementation of accelerated degradation test. In this paper, the optocoupler failure mechanism verification test is designed and the experimental results are analyzed and the prior information is obtained. The results show that optocouplers have two failure modes, one is sudden failure and the other is degradation failure; the maximum temperature stress of optocoupler can't exceed 140 °C; the increase of leakage current of optocoupler is caused by movable ions contaminating the LED chip. The surface leakage current is proportional to the adsorption amount. The increase of leakage current makes p-n junction tunneling effect occur which LEDs the failure of the optocoupler. The lifetime distribution model of the optocoupler is determined by the failure physics. The lifetime of the optocoupler is subject to the lognormal distribution. The degeneracy orbit of the optocoupler leakage current is described by a power law model. The estimated values of the orbital parameters are initially calculated and the parameters of its life distribution function are deduced. The above information lays a good foundation for the optimization design and data processing of the accelerated degradation experiment.     

试飞多目标实时定位系统的设计与实现

针对空空多目标攻击问题,运用一种基于全球定位系统(GPS)、时分多址(TDMA)和频分多址(FDMA)相结合的技术,设计了试飞多目标实时定位系统。在试飞中通过无线数据链路实时获取多个目标的GPS位置、速度数据,进行插值推算等数据融合处理后,发送给评估系统,作为空空多目标攻击技术实时评估的基准信息。系统具有定位精度高、系统数据更新率快,在实际应用中显示了良好的性能。     

Study on performance degradation and failure analysis of machine gun barrel

An increase in the use of the gun barrel will cause wear of the inner wall, which reduces the muzzle velocity and the spin rate of the projectile. The off-bore flight attitude and trajectory of the projectile also change, affecting the shooting power and the accuracy. Exterior ballistic data of a high-speed spinning projectile are required to study the performance change. Therefore, based on the barrel's accelerated life test, the whole process of projectile shooting is reproduced using numerical simulation technology, and key information on the ballistic performance change at each shooting stage are acquired. Studies have shown that in the later stages of barrel shooting, the accuracy of shooting has not decreased significantly. However, it is found that the angle of attack of the projectile increases as the wear of the barrel increases. The maximum angle of attack reaches 0.106 rad when the number of shots reaches 4300. Meanwhile, elliptical bullet hole has appeared on the target at this shooting stage. Through combining external ballistic theory with simulation results, the primary reason of this phenomenon is found to be a significant decrease in the muzzle spin rate of the projectile. At the end of the barrel life, the projectile muzzle spin rate is 57.5% lower than that of a barrel without wear.     

PMI泡沫夹层结构雷达天线罩间接热-结构耦合分析与实验研究

机载PMI泡沫夹层结构雷达天线罩在环境温度变化时将产生表面变形现象并影响其使用性能,但对天线罩热变形结果进行实时检测分析具有一定难度。通过ANSYS间接热-结构耦合法建立了分析模型,对天线罩进行了计算分析,采用热膨胀片状模型进行了理论分析,在此基础上,设计并开展了温度冲击实验研究。结果表明, PMI夹层结构天线罩的热-结构耦合变形综合应变趋势是棱边处膨胀程度最大,由边缘至天线罩透波面中心处,膨胀程度逐渐减小；间接热-结构耦合计算应变值与实测应变值之间平均相差35.08%,间接热-结构耦合分析方法与模型具有一定的可信性。     

Pairwise model discrimination with applications in lifetime distributions and degradation processes

Reliability data obtained from life tests and degradation tests have been extensively used for purposes such as estimating product reliability and predicting warranty costs. When there is more than one candidate model, an important task is to discriminate between the models. In the literature, the model discrimination was often treated as a hypothesis test and a pairwise model discrimination procedure was carried out. Because the null distribution of the test statistic is unavailable in most cases, the large sample approximation and the bootstrap were frequently used to find the acceptance region of the test. Although these two methods are asymptotically accurate, their performance in terms of size and power is not satisfactory in small sample size. To enhance the small‐sample performance, we propose a new method to approximate the null distribution, which builds on the idea of generalized pivots. Conventionally, the generalized pivots were often used for interval estimation of a certain parameter or function of parameters in presence of nuisance parameters. In this study, we further extend the idea of generalized pivots to find the acceptance region of the model discrimination test. Through extensive simulations, we show that the proposed method performs better than the existing methods in discriminating between two lifetime distributions or two degradation models over a wide range of sample sizes. Two real examples are used to illustrate the proposed methods.     

炮射导弹武器动态参数综合测试系统设计

改变传统的炮射导弹武器激光控制和火炮发射系统动态参数的测试模式，基于计算机总线技术、高速图像采集与处理技术以及激光阵元探测技术，设计了炮射导弹武器动态参数综合测试系统。详细介绍了系统的设计方案及其工作原理。该系统在野战条件下可对多种型号炮射导弹的性能进行动态参数测试及评估。